FREE Shipping at $100 *UPS Ground in the contiguous U.S.A.

2P-10 Activator, Aerosol

2P-10 Activator, Aerosol

SKU: -

SHARE:

2P-10 Activator is available in a 10 oz and 12 oz. aerosol can. Produces 10 second bond time when used with 2P-10 Adhesives.

MSDS Information

***ONLY AVAILABLE FOR UPS GROUND SHIPPING*

2P-10 Overview
2P-10 Scraping
On Hand Railing
Small Item Repair
On the Job
2P-10 and Yellow Glue
Crown Molding and 2P-10
Repair with 2P-10
2P-10 on Dave ReinholdTV
Magnetic iPhone Mount
2P-10 and MDF
2 Ways To Use 2p-10
Fix Loose Lids
Lean 2P-10
2P-10 Saves The Day
Table Saw Project
Falconboard Solutions Tools
Finger splits & 2P-10
Wood Turning Project
2P-10 Industrial Cyanoacrylate
Butt Joint
2P-10 Passed The Test!
Guitar Filling With 2P-10
Segment Wood Pen Glue
2P-10 Activator Overview
DIY - Table saw extension
2P-10 to the Rescue
Lean Problem Solving 2P-10
How To Make Wooden Corner Clamps
Build a Disposable Router Template
Miter fold PVC Trim
Kids Project: Making
Building the Impossible Bench
My Secret Weapon For Woodworking
2p-10 Mini Activator
How to fix Cabinet Doors
Zac Brown Band - My Old Man (go to 1:32)
Easy Picture Frames at Low Cost
Rock Club and 2P 10
Applying CA Glue Finish
español

2P-10 can be used on any material as long as it is clean and the surface is well prepared. The surface should be clean, with no oil, and slightly etched so the glue can bite more effectively. It should not be used in lieu of a weld (on metal), but it is very effective for tacking, to hold a piece in place.

For more information on this product press here (2P-10 TDS PDF).

For MSDS information press here (PDF).

California Residents
WARNING! This product could expose you to chemicals including N,N-dimethyl-p-toluidine which are known to the state of California to cause cancer or birth defects or other reproductive harm. For more information visit www.p65warnings.ca.gov

On what types of surfaces can I use 2P-10?

2P-10 can be used on any material as long as it is clean and the surface is well prepared. The surface should be clean, with no oil, and slightly etched so the glue can bite more effectively. It should not be used in lieu of a weld on metal, but it is very effective for tacking, to hold a piece in place.

How do I get 2P-10 Activator stain off marble, granite, terracotta, terrazzo and ceramic?

Check out this fantastic product called Mangia Macchia Stain Remover.

Mangia Macchia Stain Remover

 

How does 2P-10 stand up in a wet environment like on a boat. Can it be submerged in water?

All of our 2P-10 products are able to be submerged in water, but the adhesive must be completely bonded and DRY beforehand. All of our adhesives would work fine within a boat setting if applied correctly. You must make sure that both surfaces are dry and clear of debris before application and we also recommend that you use our 2p-10 activator to speed up the cure time.

Is there a product that will delay the bonding of the 2P-10 to allow more open time when gluing two sheets of glass together?

The 2P-10 Jel has a longer open time, up to about a 1/2 hour. If your using the thick or medium, it about 10-15 minutes. We have nothing to delay the open time but you can always have it sit in a cool dry area.

What is the open time for 2P10?

For medium, thick and jel adhesives, give it 1/2 hour before it starts to harden. the jel's open time tends to be longer because it is much thicker.

Is this comparable to the BSI C-A glue?

Yes, very similar I think. It looks like theirs is also a cyanoacrylate glue with differing possible thicknesses for different applications and with an available accelerator. I do not see where they list their percentage of CA in the mix, their bond strength, or cure times, so I don’t know exactly how similar. Ours has a 10 second set time and 30 second cure time. Ours cures at 4000 psi in both tensile and shear. Our CA is triple distilled – that means it has FAR fewer impurities than the average CA glue and does not require preservatives to stabilize it, meaning its more actual adhesive per gram. So the same size dot of ours goes further than most competitors. I cannot speak to BSI’s comparative purity, as I don’t see this info on their site (in my quick glance at it – it may be there).

Can 2P-10 Adhesive bond wood with plastic?

2p-10 can be used to bond wood and plastic with no problem. Care needs to be used with the Activator though. The Activator can cause certain plastics to discolor. 2p-10 does not need the Activator to work and in most cases where plastic is being glued, we recommend skipping the Activator

Is using glue on both pieces of wood stronger than only one side?

It only needs to be applied to 1 side; it will wet out both sides as long as you put enough on the 1 side. It can help to do both sides if the wood is very porous, but not necessary.